Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing

S. V. Panin, D. G. Buslovich, L. A. Kornienko, V. O. Alexenko, Yu V. Dontsov, B. B. Ovechkin

Результат исследований: Материалы для книги/типы отчетовМатериалы для конференции

1 цитирование (Scopus)

Выдержка

A comparative analysis on the structure, mechanical and tribological properties of the multicomponent polymer-polymeric composites "UHMWPE + 15 wt.% HDPE-g-SMA + 15 wt.% PP" fabricated by Fused Deposition Modeling (layer-by-layer extrusion printing) and hot pressing (compression sintering) was carried out. It is shown that extrudable UHMWPE composites fabricated by 3D–printing over the set of key tribomechanical properties (wear resistance, friction coefficient, elastic modulus, yield point, tensile strength, a value of elongation at break) exceed those of the composites obtained by compression sintering (CS). The reason of the latter is associated with the formation of a more uniform ordered permolecular structure with increased crystallinity. This makes it possible to recommend this material for the manufacturing complex shape products for tribotechnical applications by means of 3D-printing.

Язык оригиналаАнглийский
Название основной публикацииOil and Gas Engineering, OGE 2019
РедакторыAlexander V. Myshlyavtsev, Vladimir A. Likholobov, Vladimir L. Yusha
ИздательAmerican Institute of Physics Inc.
ISBN (электронное издание)9780735418844
DOI
СостояниеОпубликовано - 28 авг 2019
СобытиеOil and Gas Engineering Conference, OGE 2019 - Omsk, Российская Федерация
Продолжительность: 26 фев 201928 фев 2019

Серия публикаций

НазваниеAIP Conference Proceedings
Том2141
ISSN (печатное издание)0094-243X
ISSN (электронное издание)1551-7616

Конференция

КонференцияOil and Gas Engineering Conference, OGE 2019
СтранаРоссийская Федерация
ГородOmsk
Период26.2.1928.2.19

Отпечаток

composite materials
printing
polyethylene
polyethylenes
molecular weight
sintering
compression
spectral mixture analysis
hot pressing
elastic modulus
pressing
yield point
crystallinity
tensile strength
extrusion
wear resistance
friction
modulus of elasticity
coefficient of friction
elongation

ASJC Scopus subject areas

  • Ecology, Evolution, Behavior and Systematics
  • Ecology
  • Plant Science
  • Physics and Astronomy(all)
  • Nature and Landscape Conservation

Цитировать

Panin, S. V., Buslovich, D. G., Kornienko, L. A., Alexenko, V. O., Dontsov, Y. V., & Ovechkin, B. B. (2019). Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing. В A. V. Myshlyavtsev, V. A. Likholobov, & V. L. Yusha (Ред.), Oil and Gas Engineering, OGE 2019 [040011] (AIP Conference Proceedings; Том 2141). American Institute of Physics Inc.. https://doi.org/10.1063/1.5122130

Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing. / Panin, S. V.; Buslovich, D. G.; Kornienko, L. A.; Alexenko, V. O.; Dontsov, Yu V.; Ovechkin, B. B.

Oil and Gas Engineering, OGE 2019. ред. / Alexander V. Myshlyavtsev; Vladimir A. Likholobov; Vladimir L. Yusha. American Institute of Physics Inc., 2019. 040011 (AIP Conference Proceedings; Том 2141).

Результат исследований: Материалы для книги/типы отчетовМатериалы для конференции

Panin, SV, Buslovich, DG, Kornienko, LA, Alexenko, VO, Dontsov, YV & Ovechkin, BB 2019, Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing. в AV Myshlyavtsev, VA Likholobov & VL Yusha (ред.), Oil and Gas Engineering, OGE 2019., 040011, AIP Conference Proceedings, том. 2141, American Institute of Physics Inc., Oil and Gas Engineering Conference, OGE 2019, Omsk, Российская Федерация, 26.2.19. https://doi.org/10.1063/1.5122130
Panin SV, Buslovich DG, Kornienko LA, Alexenko VO, Dontsov YV, Ovechkin BB. Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing. В Myshlyavtsev AV, Likholobov VA, Yusha VL, редакторы, Oil and Gas Engineering, OGE 2019. American Institute of Physics Inc. 2019. 040011. (AIP Conference Proceedings). https://doi.org/10.1063/1.5122130
Panin, S. V. ; Buslovich, D. G. ; Kornienko, L. A. ; Alexenko, V. O. ; Dontsov, Yu V. ; Ovechkin, B. B. / Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing. Oil and Gas Engineering, OGE 2019. редактор / Alexander V. Myshlyavtsev ; Vladimir A. Likholobov ; Vladimir L. Yusha. American Institute of Physics Inc., 2019. (AIP Conference Proceedings).
@inproceedings{eef1dca1e27145a9ac5d7751441df3b5,
title = "Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing",
abstract = "A comparative analysis on the structure, mechanical and tribological properties of the multicomponent polymer-polymeric composites {"}UHMWPE + 15 wt.{\%} HDPE-g-SMA + 15 wt.{\%} PP{"} fabricated by Fused Deposition Modeling (layer-by-layer extrusion printing) and hot pressing (compression sintering) was carried out. It is shown that extrudable UHMWPE composites fabricated by 3D–printing over the set of key tribomechanical properties (wear resistance, friction coefficient, elastic modulus, yield point, tensile strength, a value of elongation at break) exceed those of the composites obtained by compression sintering (CS). The reason of the latter is associated with the formation of a more uniform ordered permolecular structure with increased crystallinity. This makes it possible to recommend this material for the manufacturing complex shape products for tribotechnical applications by means of 3D-printing.",
author = "Panin, {S. V.} and Buslovich, {D. G.} and Kornienko, {L. A.} and Alexenko, {V. O.} and Dontsov, {Yu V.} and Ovechkin, {B. B.}",
year = "2019",
month = "8",
day = "28",
doi = "10.1063/1.5122130",
language = "English",
series = "AIP Conference Proceedings",
publisher = "American Institute of Physics Inc.",
editor = "Myshlyavtsev, {Alexander V.} and Likholobov, {Vladimir A.} and Yusha, {Vladimir L.}",
booktitle = "Oil and Gas Engineering, OGE 2019",

}

TY - GEN

T1 - Structure and tribomechanical properties of extrudable ultra-high molecular weight polyethylene composites fabricated by 3D-printing

AU - Panin, S. V.

AU - Buslovich, D. G.

AU - Kornienko, L. A.

AU - Alexenko, V. O.

AU - Dontsov, Yu V.

AU - Ovechkin, B. B.

PY - 2019/8/28

Y1 - 2019/8/28

N2 - A comparative analysis on the structure, mechanical and tribological properties of the multicomponent polymer-polymeric composites "UHMWPE + 15 wt.% HDPE-g-SMA + 15 wt.% PP" fabricated by Fused Deposition Modeling (layer-by-layer extrusion printing) and hot pressing (compression sintering) was carried out. It is shown that extrudable UHMWPE composites fabricated by 3D–printing over the set of key tribomechanical properties (wear resistance, friction coefficient, elastic modulus, yield point, tensile strength, a value of elongation at break) exceed those of the composites obtained by compression sintering (CS). The reason of the latter is associated with the formation of a more uniform ordered permolecular structure with increased crystallinity. This makes it possible to recommend this material for the manufacturing complex shape products for tribotechnical applications by means of 3D-printing.

AB - A comparative analysis on the structure, mechanical and tribological properties of the multicomponent polymer-polymeric composites "UHMWPE + 15 wt.% HDPE-g-SMA + 15 wt.% PP" fabricated by Fused Deposition Modeling (layer-by-layer extrusion printing) and hot pressing (compression sintering) was carried out. It is shown that extrudable UHMWPE composites fabricated by 3D–printing over the set of key tribomechanical properties (wear resistance, friction coefficient, elastic modulus, yield point, tensile strength, a value of elongation at break) exceed those of the composites obtained by compression sintering (CS). The reason of the latter is associated with the formation of a more uniform ordered permolecular structure with increased crystallinity. This makes it possible to recommend this material for the manufacturing complex shape products for tribotechnical applications by means of 3D-printing.

UR - http://www.scopus.com/inward/record.url?scp=85072108765&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85072108765&partnerID=8YFLogxK

U2 - 10.1063/1.5122130

DO - 10.1063/1.5122130

M3 - Conference contribution

AN - SCOPUS:85072108765

T3 - AIP Conference Proceedings

BT - Oil and Gas Engineering, OGE 2019

A2 - Myshlyavtsev, Alexander V.

A2 - Likholobov, Vladimir A.

A2 - Yusha, Vladimir L.

PB - American Institute of Physics Inc.

ER -