Computer simulation of oil and gas flow line stress-strain behavior

Результат исследований: Материалы для книги/типы отчетовМатериалы для конференции

Выдержка

Flow lines are one of the key elements of oil field facilities as they ensure safe transport of raw multiphase mixtures of gas, oil and water from reservoir to reception facilities. The growth of oil extraction in Russia makes the issue of developing new deposits and maintaining high production of oil and gas from existing ones particularly important. Therefore, maintenance of flow lines in service is of great significance. Most of Russia’s oil production originates in West Siberia. The territory is characterized with considerable annual and daily fluctuations of temperature, high precipitation, and vast wetlands. A specific challenge is to maintain underground sections of pipeline constructed under severe climatic conditions. Pipeline failures and accidents operated under harsh climatic conditions are primarily induced by bending deformation accompanied with soil-pipe-fluid (gas) displacements. To prevent accidents that could be caused by excessive bending deformations, it is essential to analyze the impact of climatic conditions, soils, and operation parameters, as well as to reveal the most potentially dangerous pipeline sections. To detect the most dangerous sections, alongside with various technical tools and equipment, pipeline strength and stability are calculated. The following regulative documents that prescribe the procedure of underground pipeline strength calculation SNiP (construction rules and regulations) 2.05.06-85* “Transmission pipelines” (section 8.25), set of rules 34-116-97 “Instruction on oil and gas flow line design, construction, and repair” (section 8.1) state the requirements for simulating soil-pipe interaction. The search for new methods to calculate strain-stress behavior of underground pipelines is of particular importance as due to the great length of pipeline the increase in pipe wall thickness at least by 1 mm leads to significant overspend. It is worth noting that soil is not the only source of external load, but also serves as an environment where pipe deformations occur. At the same time, these documents do not explain the calculation procedure itself. The remaining time (RT) is estimated as the time over which defects accumulate until ultimate limit state is reached. As a rule, the procedure of RT calculation is not detailed. The calculations are done on the basis of formulas used for estimating facility life time according to the deterministic and probabilistic schemes. When using deterministic methods, the fixed data on fracture toughness, loads on pipelines and pipe defects are considered. The remaining time is predicted on the basis of safety coefficients (fracture resistance) and survivability. RT is defined as a moment when hypothetical cracks or cracks existing in the pipeline are in compliance with the safety requirements for the damaged system based on the criteria of fracture mechanics and survivability. To perform probability calculations, the reliability theory which rests on the statistic.

Язык оригиналаАнглийский
Название основной публикацииMicro and Nano Technologies, Space Technologies and Planetary Science
ИздательInternational Multidisciplinary Scientific Geoconference
Страницы343-350
Число страниц8
Издание1.4
ISBN (электронное издание)9786197408355, 9786197408362, 9786197408379, 9786197408386, 9786197408393, 9786197408409, 9786197408416, 9786197408423, 9786197408430, 9786197408447, 9786197408454, 9786197408461, 9786197408478, 9786197408485, 9786197408492, 9786197408508, 9786197408515, 9786197408522
ISBN (печатное издание)9786197408355
DOI
СостояниеОпубликовано - 1 янв 2018
Событие18th International Multidisciplinary Scientific Geoconference, SGEM 2018 - Albena, Болгария
Продолжительность: 2 июл 20188 июл 2018

Серия публикаций

НазваниеInternational Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM
Номер1.4
Том18
ISSN (печатное издание)1314-2704

Конференция

Конференция18th International Multidisciplinary Scientific Geoconference, SGEM 2018
СтранаБолгария
ГородAlbena
Период2.7.188.7.18

Отпечаток

gas flow
computer simulation
Flow of gases
Pipelines
oil
Computer simulation
pipe
Pipe
Soils
accident
defect
Fracture toughness
Accidents
crack
gas
Oils
safety
Cracks
Reliability theory
Defects

ASJC Scopus subject areas

  • Geotechnical Engineering and Engineering Geology
  • Geology

Цитировать

Burkov, P., Burkov, V., & Burkova, S. (2018). Computer simulation of oil and gas flow line stress-strain behavior. В Micro and Nano Technologies, Space Technologies and Planetary Science (1.4 ред., стр. 343-350). (International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM; Том 18, № 1.4). International Multidisciplinary Scientific Geoconference. https://doi.org/10.5593/sgem2018/1.4/S06.045

Computer simulation of oil and gas flow line stress-strain behavior. / Burkov, Peter; Burkov, Vladimir; Burkova, Svetlana.

Micro and Nano Technologies, Space Technologies and Planetary Science. 1.4. ред. International Multidisciplinary Scientific Geoconference, 2018. стр. 343-350 (International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM; Том 18, № 1.4).

Результат исследований: Материалы для книги/типы отчетовМатериалы для конференции

Burkov, P, Burkov, V & Burkova, S 2018, Computer simulation of oil and gas flow line stress-strain behavior. в Micro and Nano Technologies, Space Technologies and Planetary Science. 1.4 ред., International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM, № 1.4, том. 18, International Multidisciplinary Scientific Geoconference, стр. 343-350, Albena, Болгария, 2.7.18. https://doi.org/10.5593/sgem2018/1.4/S06.045
Burkov P, Burkov V, Burkova S. Computer simulation of oil and gas flow line stress-strain behavior. В Micro and Nano Technologies, Space Technologies and Planetary Science. 1.4 ред. International Multidisciplinary Scientific Geoconference. 2018. стр. 343-350. (International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM; 1.4). https://doi.org/10.5593/sgem2018/1.4/S06.045
Burkov, Peter ; Burkov, Vladimir ; Burkova, Svetlana. / Computer simulation of oil and gas flow line stress-strain behavior. Micro and Nano Technologies, Space Technologies and Planetary Science. 1.4. ред. International Multidisciplinary Scientific Geoconference, 2018. стр. 343-350 (International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM; 1.4).
@inproceedings{68d5b344d40a4df1bcb5b70078b8af75,
title = "Computer simulation of oil and gas flow line stress-strain behavior",
abstract = "Flow lines are one of the key elements of oil field facilities as they ensure safe transport of raw multiphase mixtures of gas, oil and water from reservoir to reception facilities. The growth of oil extraction in Russia makes the issue of developing new deposits and maintaining high production of oil and gas from existing ones particularly important. Therefore, maintenance of flow lines in service is of great significance. Most of Russia’s oil production originates in West Siberia. The territory is characterized with considerable annual and daily fluctuations of temperature, high precipitation, and vast wetlands. A specific challenge is to maintain underground sections of pipeline constructed under severe climatic conditions. Pipeline failures and accidents operated under harsh climatic conditions are primarily induced by bending deformation accompanied with soil-pipe-fluid (gas) displacements. To prevent accidents that could be caused by excessive bending deformations, it is essential to analyze the impact of climatic conditions, soils, and operation parameters, as well as to reveal the most potentially dangerous pipeline sections. To detect the most dangerous sections, alongside with various technical tools and equipment, pipeline strength and stability are calculated. The following regulative documents that prescribe the procedure of underground pipeline strength calculation SNiP (construction rules and regulations) 2.05.06-85* “Transmission pipelines” (section 8.25), set of rules 34-116-97 “Instruction on oil and gas flow line design, construction, and repair” (section 8.1) state the requirements for simulating soil-pipe interaction. The search for new methods to calculate strain-stress behavior of underground pipelines is of particular importance as due to the great length of pipeline the increase in pipe wall thickness at least by 1 mm leads to significant overspend. It is worth noting that soil is not the only source of external load, but also serves as an environment where pipe deformations occur. At the same time, these documents do not explain the calculation procedure itself. The remaining time (RT) is estimated as the time over which defects accumulate until ultimate limit state is reached. As a rule, the procedure of RT calculation is not detailed. The calculations are done on the basis of formulas used for estimating facility life time according to the deterministic and probabilistic schemes. When using deterministic methods, the fixed data on fracture toughness, loads on pipelines and pipe defects are considered. The remaining time is predicted on the basis of safety coefficients (fracture resistance) and survivability. RT is defined as a moment when hypothetical cracks or cracks existing in the pipeline are in compliance with the safety requirements for the damaged system based on the criteria of fracture mechanics and survivability. To perform probability calculations, the reliability theory which rests on the statistic.",
keywords = "Pipe wall thickness, Strain, Stress calculation",
author = "Peter Burkov and Vladimir Burkov and Svetlana Burkova",
year = "2018",
month = "1",
day = "1",
doi = "10.5593/sgem2018/1.4/S06.045",
language = "English",
isbn = "9786197408355",
series = "International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM",
publisher = "International Multidisciplinary Scientific Geoconference",
number = "1.4",
pages = "343--350",
booktitle = "Micro and Nano Technologies, Space Technologies and Planetary Science",
edition = "1.4",

}

TY - GEN

T1 - Computer simulation of oil and gas flow line stress-strain behavior

AU - Burkov, Peter

AU - Burkov, Vladimir

AU - Burkova, Svetlana

PY - 2018/1/1

Y1 - 2018/1/1

N2 - Flow lines are one of the key elements of oil field facilities as they ensure safe transport of raw multiphase mixtures of gas, oil and water from reservoir to reception facilities. The growth of oil extraction in Russia makes the issue of developing new deposits and maintaining high production of oil and gas from existing ones particularly important. Therefore, maintenance of flow lines in service is of great significance. Most of Russia’s oil production originates in West Siberia. The territory is characterized with considerable annual and daily fluctuations of temperature, high precipitation, and vast wetlands. A specific challenge is to maintain underground sections of pipeline constructed under severe climatic conditions. Pipeline failures and accidents operated under harsh climatic conditions are primarily induced by bending deformation accompanied with soil-pipe-fluid (gas) displacements. To prevent accidents that could be caused by excessive bending deformations, it is essential to analyze the impact of climatic conditions, soils, and operation parameters, as well as to reveal the most potentially dangerous pipeline sections. To detect the most dangerous sections, alongside with various technical tools and equipment, pipeline strength and stability are calculated. The following regulative documents that prescribe the procedure of underground pipeline strength calculation SNiP (construction rules and regulations) 2.05.06-85* “Transmission pipelines” (section 8.25), set of rules 34-116-97 “Instruction on oil and gas flow line design, construction, and repair” (section 8.1) state the requirements for simulating soil-pipe interaction. The search for new methods to calculate strain-stress behavior of underground pipelines is of particular importance as due to the great length of pipeline the increase in pipe wall thickness at least by 1 mm leads to significant overspend. It is worth noting that soil is not the only source of external load, but also serves as an environment where pipe deformations occur. At the same time, these documents do not explain the calculation procedure itself. The remaining time (RT) is estimated as the time over which defects accumulate until ultimate limit state is reached. As a rule, the procedure of RT calculation is not detailed. The calculations are done on the basis of formulas used for estimating facility life time according to the deterministic and probabilistic schemes. When using deterministic methods, the fixed data on fracture toughness, loads on pipelines and pipe defects are considered. The remaining time is predicted on the basis of safety coefficients (fracture resistance) and survivability. RT is defined as a moment when hypothetical cracks or cracks existing in the pipeline are in compliance with the safety requirements for the damaged system based on the criteria of fracture mechanics and survivability. To perform probability calculations, the reliability theory which rests on the statistic.

AB - Flow lines are one of the key elements of oil field facilities as they ensure safe transport of raw multiphase mixtures of gas, oil and water from reservoir to reception facilities. The growth of oil extraction in Russia makes the issue of developing new deposits and maintaining high production of oil and gas from existing ones particularly important. Therefore, maintenance of flow lines in service is of great significance. Most of Russia’s oil production originates in West Siberia. The territory is characterized with considerable annual and daily fluctuations of temperature, high precipitation, and vast wetlands. A specific challenge is to maintain underground sections of pipeline constructed under severe climatic conditions. Pipeline failures and accidents operated under harsh climatic conditions are primarily induced by bending deformation accompanied with soil-pipe-fluid (gas) displacements. To prevent accidents that could be caused by excessive bending deformations, it is essential to analyze the impact of climatic conditions, soils, and operation parameters, as well as to reveal the most potentially dangerous pipeline sections. To detect the most dangerous sections, alongside with various technical tools and equipment, pipeline strength and stability are calculated. The following regulative documents that prescribe the procedure of underground pipeline strength calculation SNiP (construction rules and regulations) 2.05.06-85* “Transmission pipelines” (section 8.25), set of rules 34-116-97 “Instruction on oil and gas flow line design, construction, and repair” (section 8.1) state the requirements for simulating soil-pipe interaction. The search for new methods to calculate strain-stress behavior of underground pipelines is of particular importance as due to the great length of pipeline the increase in pipe wall thickness at least by 1 mm leads to significant overspend. It is worth noting that soil is not the only source of external load, but also serves as an environment where pipe deformations occur. At the same time, these documents do not explain the calculation procedure itself. The remaining time (RT) is estimated as the time over which defects accumulate until ultimate limit state is reached. As a rule, the procedure of RT calculation is not detailed. The calculations are done on the basis of formulas used for estimating facility life time according to the deterministic and probabilistic schemes. When using deterministic methods, the fixed data on fracture toughness, loads on pipelines and pipe defects are considered. The remaining time is predicted on the basis of safety coefficients (fracture resistance) and survivability. RT is defined as a moment when hypothetical cracks or cracks existing in the pipeline are in compliance with the safety requirements for the damaged system based on the criteria of fracture mechanics and survivability. To perform probability calculations, the reliability theory which rests on the statistic.

KW - Pipe wall thickness

KW - Strain

KW - Stress calculation

UR - http://www.scopus.com/inward/record.url?scp=85058874802&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85058874802&partnerID=8YFLogxK

U2 - 10.5593/sgem2018/1.4/S06.045

DO - 10.5593/sgem2018/1.4/S06.045

M3 - Conference contribution

AN - SCOPUS:85058874802

SN - 9786197408355

T3 - International Multidisciplinary Scientific GeoConference Surveying Geology and Mining Ecology Management, SGEM

SP - 343

EP - 350

BT - Micro and Nano Technologies, Space Technologies and Planetary Science

PB - International Multidisciplinary Scientific Geoconference

ER -