Polymer optical microring filter for passive optical network applications

V. Prajzler, E. Střílek, O. Lyutakov, I. Hüttel, J. Špirková, V. Jurka, V. Jeřábek

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

We report about design, fabrication and properties of the polymer optical microring resonator and coupled optical microring resonator filters operating at 1490 nm. The resonator was fabricated by using Epoxy Novolak Resin onto silica on silicon substrate. We started with designing single mode rib waveguides by using BeamPROP software and the obtained results were then capitalized to design microring resonator by using FullWAVE software, which is part of the RSoft software. The design of the MR has FWHM 22 nm and FSR 44 nm and the resonator was fabricated by using electron beam lithography.

Original languageEnglish
Title of host publication2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf
Pages1297-1299
Number of pages3
DOIs
Publication statusPublished - 1 Dec 2011
Externally publishedYes
Event2011 International Quantum Electronics Conference, IQEC 2011 and Conference on Lasers and Electro-Optics, CLEO Pacific Rim 2011 - Sydney, NSW, Australia
Duration: 28 Aug 20111 Sep 2011

Publication series

Name2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.

Conference

Conference2011 International Quantum Electronics Conference, IQEC 2011 and Conference on Lasers and Electro-Optics, CLEO Pacific Rim 2011
CountryAustralia
CitySydney, NSW
Period28.8.111.9.11

Fingerprint

Passive optical networks
Optical filters
Optical resonators
Resonators
Polymers
Electron beam lithography
Full width at half maximum
Epoxy resins
Waveguides
Silica
Fabrication
Silicon
Substrates

ASJC Scopus subject areas

  • Electrical and Electronic Engineering

Cite this

Prajzler, V., Střílek, E., Lyutakov, O., Hüttel, I., Špirková, J., Jurka, V., & Jeřábek, V. (2011). Polymer optical microring filter for passive optical network applications. In 2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf (pp. 1297-1299). [6193633] (2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.). https://doi.org/10.1109/IQEC-CLEO.2011.6193633

Polymer optical microring filter for passive optical network applications. / Prajzler, V.; Střílek, E.; Lyutakov, O.; Hüttel, I.; Špirková, J.; Jurka, V.; Jeřábek, V.

2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf. 2011. p. 1297-1299 6193633 (2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Prajzler, V, Střílek, E, Lyutakov, O, Hüttel, I, Špirková, J, Jurka, V & Jeřábek, V 2011, Polymer optical microring filter for passive optical network applications. in 2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf., 6193633, 2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf., pp. 1297-1299, 2011 International Quantum Electronics Conference, IQEC 2011 and Conference on Lasers and Electro-Optics, CLEO Pacific Rim 2011, Sydney, NSW, Australia, 28.8.11. https://doi.org/10.1109/IQEC-CLEO.2011.6193633
Prajzler V, Střílek E, Lyutakov O, Hüttel I, Špirková J, Jurka V et al. Polymer optical microring filter for passive optical network applications. In 2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf. 2011. p. 1297-1299. 6193633. (2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.). https://doi.org/10.1109/IQEC-CLEO.2011.6193633
Prajzler, V. ; Střílek, E. ; Lyutakov, O. ; Hüttel, I. ; Špirková, J. ; Jurka, V. ; Jeřábek, V. / Polymer optical microring filter for passive optical network applications. 2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf. 2011. pp. 1297-1299 (2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.).
@inproceedings{1b542d9c924a4fc58a41b800cfe5785e,
title = "Polymer optical microring filter for passive optical network applications",
abstract = "We report about design, fabrication and properties of the polymer optical microring resonator and coupled optical microring resonator filters operating at 1490 nm. The resonator was fabricated by using Epoxy Novolak Resin onto silica on silicon substrate. We started with designing single mode rib waveguides by using BeamPROP software and the obtained results were then capitalized to design microring resonator by using FullWAVE software, which is part of the RSoft software. The design of the MR has FWHM 22 nm and FSR 44 nm and the resonator was fabricated by using electron beam lithography.",
author = "V. Prajzler and E. Stř{\'i}lek and O. Lyutakov and I. H{\"u}ttel and J. Špirkov{\'a} and V. Jurka and V. Jeř{\'a}bek",
year = "2011",
month = "12",
day = "1",
doi = "10.1109/IQEC-CLEO.2011.6193633",
language = "English",
isbn = "9780977565771",
series = "2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.",
pages = "1297--1299",
booktitle = "2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf",

}

TY - GEN

T1 - Polymer optical microring filter for passive optical network applications

AU - Prajzler, V.

AU - Střílek, E.

AU - Lyutakov, O.

AU - Hüttel, I.

AU - Špirková, J.

AU - Jurka, V.

AU - Jeřábek, V.

PY - 2011/12/1

Y1 - 2011/12/1

N2 - We report about design, fabrication and properties of the polymer optical microring resonator and coupled optical microring resonator filters operating at 1490 nm. The resonator was fabricated by using Epoxy Novolak Resin onto silica on silicon substrate. We started with designing single mode rib waveguides by using BeamPROP software and the obtained results were then capitalized to design microring resonator by using FullWAVE software, which is part of the RSoft software. The design of the MR has FWHM 22 nm and FSR 44 nm and the resonator was fabricated by using electron beam lithography.

AB - We report about design, fabrication and properties of the polymer optical microring resonator and coupled optical microring resonator filters operating at 1490 nm. The resonator was fabricated by using Epoxy Novolak Resin onto silica on silicon substrate. We started with designing single mode rib waveguides by using BeamPROP software and the obtained results were then capitalized to design microring resonator by using FullWAVE software, which is part of the RSoft software. The design of the MR has FWHM 22 nm and FSR 44 nm and the resonator was fabricated by using electron beam lithography.

UR - http://www.scopus.com/inward/record.url?scp=84862077997&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84862077997&partnerID=8YFLogxK

U2 - 10.1109/IQEC-CLEO.2011.6193633

DO - 10.1109/IQEC-CLEO.2011.6193633

M3 - Conference contribution

SN - 9780977565771

T3 - 2011 Int. Quantum Electron. Conf., IQEC 2011 and Conf. Lasers and Electro-Optics, CLEO Pacific Rim 2011 Incorporating the Australasian Conf. Optics, Lasers and Spectroscopy and the Australian Conf.

SP - 1297

EP - 1299

BT - 2011 Int. Quantum Electr. Conf., IQEC 2011 Conf Lasers Electro-Optics, CLEO Pacific Rim 2011 Incorporating Australasian Conf. on Optics, Lasers Spectrosc. Australian Conf. Optical Fibre Technol.- Conf

ER -