Method of determining the optimal concentration of nanostructured powders in shielding gas

S. A. Barannikova, G. V. Shlyakhova, E. A. Zernin, M. A. Kuznetsov

Research output: Contribution to journalArticle

Abstract

The paper presents the theoretical and experimental studies to determine the optimal concentration of nanostructured powders in the shielding gas. The objective of this study is the development of a definition technique for optimal concentration of nanostructured powders in the shielding gas during welding by consumable electrode in the argon medium. Molybdenum nanopowder (NP Mo) was used to confirm the calculations used in the experimental studies. The injection of the powder into the weld bath was carried out through the special device. The surfacing of samples was carried out in a pilot plant, which consisted of a welding head GSP-2 with the developed device, the power supply had rated current of 300 A. For surfacing of steel samples (austenitic steel with chemical composition: C – 0.12 %, Cr – 18 %, Ni – 10 %, Ti – 1 %) the welding wire with diameter of 1.2 mm was used (chemical composition: C – 0.12 %, Cr – 18 %, Ni – 9 %, Ti – 1 %,). To ensure the quality of the welded joint during welding, the dimension parameters of dendrites should tend to a minimum. A stable welding process is caused by the transition of electrode metal droplets from the end of the welding wire into the weld bath. Therefore, the volume of the electrode metal droplet should also tend to a minimum. Before the start of the optimization of nanostructured powders concentration in the shielding gas, the effect of welding mode parameters by consumable electrode in the argon medium on the microstructure of the weld metal was established. The results of the investigations have shown that the minimum grain size is observed at a current strength of 240 – 260 A and arc voltage of 28 – 30 V. In these modes, the studies were conducted to select the optimum concentration of nanostructured powders in the shielding gas. It was found that the optimum concentration of nanostructured powders-modifiers in the shielding gas is 20 mg/m of the welded joint. It was established that the use of different concentrations of nanostructured powders in the shielding gas makes it possible to obtain a different microstructure of the weld metal. The most lightly branched dendrites and the equilibrium structure according to the dendrites size are achieved at a concentration of nanostructured powder in the shielding gas of 20 mg/m of the weld. When adding nanostructured powders-modifiers to a liquid weld bath, the mechanical properties of the welded joints increase as compared to the welding process, without the addition of a powder-modifier at +20 °C by 7.5 %, at +500 °C by 6.5 %.

Original languageEnglish
Pages (from-to)292-297
Number of pages6
JournalIzvestiya Ferrous Metallurgy
Volume60
Issue number4
DOIs
Publication statusPublished - 1 Jan 2017

Fingerprint

Shielding
Powders
Gases
Welds
Welding
Metals
Electrodes
Hard facing
Argon
Wire
Gas welding
Microstructure
Dendrites (metallography)
Molybdenum
Austenitic steel
Chemical analysis
Pilot plants
Mechanical properties
Steel
Liquids

Keywords

  • Crystallization
  • Multifactorial planning
  • Nanostructured powders
  • Optimal concentration
  • Shielding gas
  • Weld bath

ASJC Scopus subject areas

  • Materials Science (miscellaneous)
  • Metals and Alloys

Cite this

Method of determining the optimal concentration of nanostructured powders in shielding gas. / Barannikova, S. A.; Shlyakhova, G. V.; Zernin, E. A.; Kuznetsov, M. A.

In: Izvestiya Ferrous Metallurgy, Vol. 60, No. 4, 01.01.2017, p. 292-297.

Research output: Contribution to journalArticle

@article{3b11170c26654cffaf8a61c4a8c8b13c,
title = "Method of determining the optimal concentration of nanostructured powders in shielding gas",
abstract = "The paper presents the theoretical and experimental studies to determine the optimal concentration of nanostructured powders in the shielding gas. The objective of this study is the development of a definition technique for optimal concentration of nanostructured powders in the shielding gas during welding by consumable electrode in the argon medium. Molybdenum nanopowder (NP Mo) was used to confirm the calculations used in the experimental studies. The injection of the powder into the weld bath was carried out through the special device. The surfacing of samples was carried out in a pilot plant, which consisted of a welding head GSP-2 with the developed device, the power supply had rated current of 300 A. For surfacing of steel samples (austenitic steel with chemical composition: C – 0.12 {\%}, Cr – 18 {\%}, Ni – 10 {\%}, Ti – 1 {\%}) the welding wire with diameter of 1.2 mm was used (chemical composition: C – 0.12 {\%}, Cr – 18 {\%}, Ni – 9 {\%}, Ti – 1 {\%},). To ensure the quality of the welded joint during welding, the dimension parameters of dendrites should tend to a minimum. A stable welding process is caused by the transition of electrode metal droplets from the end of the welding wire into the weld bath. Therefore, the volume of the electrode metal droplet should also tend to a minimum. Before the start of the optimization of nanostructured powders concentration in the shielding gas, the effect of welding mode parameters by consumable electrode in the argon medium on the microstructure of the weld metal was established. The results of the investigations have shown that the minimum grain size is observed at a current strength of 240 – 260 A and arc voltage of 28 – 30 V. In these modes, the studies were conducted to select the optimum concentration of nanostructured powders in the shielding gas. It was found that the optimum concentration of nanostructured powders-modifiers in the shielding gas is 20 mg/m of the welded joint. It was established that the use of different concentrations of nanostructured powders in the shielding gas makes it possible to obtain a different microstructure of the weld metal. The most lightly branched dendrites and the equilibrium structure according to the dendrites size are achieved at a concentration of nanostructured powder in the shielding gas of 20 mg/m of the weld. When adding nanostructured powders-modifiers to a liquid weld bath, the mechanical properties of the welded joints increase as compared to the welding process, without the addition of a powder-modifier at +20 °C by 7.5 {\%}, at +500 °C by 6.5 {\%}.",
keywords = "Crystallization, Multifactorial planning, Nanostructured powders, Optimal concentration, Shielding gas, Weld bath",
author = "Barannikova, {S. A.} and Shlyakhova, {G. V.} and Zernin, {E. A.} and Kuznetsov, {M. A.}",
year = "2017",
month = "1",
day = "1",
doi = "10.17073/0368-0797-2017-4-292-297",
language = "English",
volume = "60",
pages = "292--297",
journal = "Izvestiya Vysshikh Uchebnykh Zavedenij. Chernaya Metallurgiya",
issn = "0368-0797",
publisher = "Moskovskii Gosudarstvennyi Institut Stali i Splavov",
number = "4",

}

TY - JOUR

T1 - Method of determining the optimal concentration of nanostructured powders in shielding gas

AU - Barannikova, S. A.

AU - Shlyakhova, G. V.

AU - Zernin, E. A.

AU - Kuznetsov, M. A.

PY - 2017/1/1

Y1 - 2017/1/1

N2 - The paper presents the theoretical and experimental studies to determine the optimal concentration of nanostructured powders in the shielding gas. The objective of this study is the development of a definition technique for optimal concentration of nanostructured powders in the shielding gas during welding by consumable electrode in the argon medium. Molybdenum nanopowder (NP Mo) was used to confirm the calculations used in the experimental studies. The injection of the powder into the weld bath was carried out through the special device. The surfacing of samples was carried out in a pilot plant, which consisted of a welding head GSP-2 with the developed device, the power supply had rated current of 300 A. For surfacing of steel samples (austenitic steel with chemical composition: C – 0.12 %, Cr – 18 %, Ni – 10 %, Ti – 1 %) the welding wire with diameter of 1.2 mm was used (chemical composition: C – 0.12 %, Cr – 18 %, Ni – 9 %, Ti – 1 %,). To ensure the quality of the welded joint during welding, the dimension parameters of dendrites should tend to a minimum. A stable welding process is caused by the transition of electrode metal droplets from the end of the welding wire into the weld bath. Therefore, the volume of the electrode metal droplet should also tend to a minimum. Before the start of the optimization of nanostructured powders concentration in the shielding gas, the effect of welding mode parameters by consumable electrode in the argon medium on the microstructure of the weld metal was established. The results of the investigations have shown that the minimum grain size is observed at a current strength of 240 – 260 A and arc voltage of 28 – 30 V. In these modes, the studies were conducted to select the optimum concentration of nanostructured powders in the shielding gas. It was found that the optimum concentration of nanostructured powders-modifiers in the shielding gas is 20 mg/m of the welded joint. It was established that the use of different concentrations of nanostructured powders in the shielding gas makes it possible to obtain a different microstructure of the weld metal. The most lightly branched dendrites and the equilibrium structure according to the dendrites size are achieved at a concentration of nanostructured powder in the shielding gas of 20 mg/m of the weld. When adding nanostructured powders-modifiers to a liquid weld bath, the mechanical properties of the welded joints increase as compared to the welding process, without the addition of a powder-modifier at +20 °C by 7.5 %, at +500 °C by 6.5 %.

AB - The paper presents the theoretical and experimental studies to determine the optimal concentration of nanostructured powders in the shielding gas. The objective of this study is the development of a definition technique for optimal concentration of nanostructured powders in the shielding gas during welding by consumable electrode in the argon medium. Molybdenum nanopowder (NP Mo) was used to confirm the calculations used in the experimental studies. The injection of the powder into the weld bath was carried out through the special device. The surfacing of samples was carried out in a pilot plant, which consisted of a welding head GSP-2 with the developed device, the power supply had rated current of 300 A. For surfacing of steel samples (austenitic steel with chemical composition: C – 0.12 %, Cr – 18 %, Ni – 10 %, Ti – 1 %) the welding wire with diameter of 1.2 mm was used (chemical composition: C – 0.12 %, Cr – 18 %, Ni – 9 %, Ti – 1 %,). To ensure the quality of the welded joint during welding, the dimension parameters of dendrites should tend to a minimum. A stable welding process is caused by the transition of electrode metal droplets from the end of the welding wire into the weld bath. Therefore, the volume of the electrode metal droplet should also tend to a minimum. Before the start of the optimization of nanostructured powders concentration in the shielding gas, the effect of welding mode parameters by consumable electrode in the argon medium on the microstructure of the weld metal was established. The results of the investigations have shown that the minimum grain size is observed at a current strength of 240 – 260 A and arc voltage of 28 – 30 V. In these modes, the studies were conducted to select the optimum concentration of nanostructured powders in the shielding gas. It was found that the optimum concentration of nanostructured powders-modifiers in the shielding gas is 20 mg/m of the welded joint. It was established that the use of different concentrations of nanostructured powders in the shielding gas makes it possible to obtain a different microstructure of the weld metal. The most lightly branched dendrites and the equilibrium structure according to the dendrites size are achieved at a concentration of nanostructured powder in the shielding gas of 20 mg/m of the weld. When adding nanostructured powders-modifiers to a liquid weld bath, the mechanical properties of the welded joints increase as compared to the welding process, without the addition of a powder-modifier at +20 °C by 7.5 %, at +500 °C by 6.5 %.

KW - Crystallization

KW - Multifactorial planning

KW - Nanostructured powders

KW - Optimal concentration

KW - Shielding gas

KW - Weld bath

UR - http://www.scopus.com/inward/record.url?scp=85026395349&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85026395349&partnerID=8YFLogxK

U2 - 10.17073/0368-0797-2017-4-292-297

DO - 10.17073/0368-0797-2017-4-292-297

M3 - Article

AN - SCOPUS:85026395349

VL - 60

SP - 292

EP - 297

JO - Izvestiya Vysshikh Uchebnykh Zavedenij. Chernaya Metallurgiya

JF - Izvestiya Vysshikh Uchebnykh Zavedenij. Chernaya Metallurgiya

SN - 0368-0797

IS - 4

ER -