Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application

I. Grubova, E. Chudinova, M. Surmeneva, R. Surmenev, A. Ivanova, K. S. Kravchuk, V. V. Shugurov, A. D. Teresov, N. Koval, O. Prymak, M. Epple

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

Modification of the surface topography and chemistry are commonly used to achieve the desired biological response to the implants. The influence of the different treatment methods on the physicochemical and mechanical properties of titanium is reported. All samples were divided into 2 groups. First group was sandblasted with 250-320 μm Al2O3 at two pressures 0.45 MPa and 0.61 MPa followed by the chemical etching in a fluorine-containing solution. The second group was acid-etched in the same solution followed by electron beam modification with the energy density 8 J/cm2. The samples were investigated by SEM, EDX, XRD, nanoindentation and sessile drop method. The studies revealed that all groups have nano/micro-patterned surfaces. The EDX analysis detected only titanium in all groups. The XRD results revealed the presence of diffraction peaks corresponding to titanium. The nanoindentation studies revealed significant differences in the mechanical properties between group 1 and 2. The elastic strain to failure and plastic deformation resistance of the group 2 were determined to be 0.035 and 5∗10-3, respectively, which were significantly higher than those of group 1. The obtained results of water contact angle for group 1 revealed moderately hydrophilic properties of treated surfaces. The water contact angle was increased up to 80.85 ± 8.3 ° for group 2.

Original languageEnglish
Title of host publicationProceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016
PublisherInstitute of Electrical and Electronics Engineers Inc.
Pages69-72
Number of pages4
ISBN (Electronic)9781509008551
DOIs
Publication statusPublished - 21 Mar 2017
Event11th International Forum on Strategic Technology, IFOST 2016 - Novosibirsk, Russian Federation
Duration: 1 Jun 20163 Jun 2016

Conference

Conference11th International Forum on Strategic Technology, IFOST 2016
CountryRussian Federation
CityNovosibirsk
Period1.6.163.6.16

Fingerprint

Surface Treatment
Medical Applications
Titanium
Medical applications
Blasting
Etching
Electron Beam
Surface treatment
Electron beams
Sand
Nanoindentation
Contact angle
Acids
Energy dispersive spectroscopy
Evaluation
Mechanical properties
Fluorine
Water
Surface topography
Surface chemistry

Keywords

  • acid etching
  • biocompatibility
  • electron beam
  • sand blasting
  • titanium

ASJC Scopus subject areas

  • Ceramics and Composites
  • Computational Mathematics
  • Computer Science Applications
  • Mechanical Engineering
  • Mechanics of Materials
  • Electronic, Optical and Magnetic Materials
  • Control and Optimization

Cite this

Grubova, I., Chudinova, E., Surmeneva, M., Surmenev, R., Ivanova, A., Kravchuk, K. S., ... Epple, M. (2017). Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application. In Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016 (pp. 69-72). [7884191] Institute of Electrical and Electronics Engineers Inc.. https://doi.org/10.1109/IFOST.2016.7884191

Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application. / Grubova, I.; Chudinova, E.; Surmeneva, M.; Surmenev, R.; Ivanova, A.; Kravchuk, K. S.; Shugurov, V. V.; Teresov, A. D.; Koval, N.; Prymak, O.; Epple, M.

Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016. Institute of Electrical and Electronics Engineers Inc., 2017. p. 69-72 7884191.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Grubova, I, Chudinova, E, Surmeneva, M, Surmenev, R, Ivanova, A, Kravchuk, KS, Shugurov, VV, Teresov, AD, Koval, N, Prymak, O & Epple, M 2017, Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application. in Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016., 7884191, Institute of Electrical and Electronics Engineers Inc., pp. 69-72, 11th International Forum on Strategic Technology, IFOST 2016, Novosibirsk, Russian Federation, 1.6.16. https://doi.org/10.1109/IFOST.2016.7884191
Grubova I, Chudinova E, Surmeneva M, Surmenev R, Ivanova A, Kravchuk KS et al. Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application. In Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016. Institute of Electrical and Electronics Engineers Inc. 2017. p. 69-72. 7884191 https://doi.org/10.1109/IFOST.2016.7884191
Grubova, I. ; Chudinova, E. ; Surmeneva, M. ; Surmenev, R. ; Ivanova, A. ; Kravchuk, K. S. ; Shugurov, V. V. ; Teresov, A. D. ; Koval, N. ; Prymak, O. ; Epple, M. / Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application. Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016. Institute of Electrical and Electronics Engineers Inc., 2017. pp. 69-72
@inproceedings{59d4ac10a22247b98ec3100da535de4b,
title = "Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application",
abstract = "Modification of the surface topography and chemistry are commonly used to achieve the desired biological response to the implants. The influence of the different treatment methods on the physicochemical and mechanical properties of titanium is reported. All samples were divided into 2 groups. First group was sandblasted with 250-320 μm Al2O3 at two pressures 0.45 MPa and 0.61 MPa followed by the chemical etching in a fluorine-containing solution. The second group was acid-etched in the same solution followed by electron beam modification with the energy density 8 J/cm2. The samples were investigated by SEM, EDX, XRD, nanoindentation and sessile drop method. The studies revealed that all groups have nano/micro-patterned surfaces. The EDX analysis detected only titanium in all groups. The XRD results revealed the presence of diffraction peaks corresponding to titanium. The nanoindentation studies revealed significant differences in the mechanical properties between group 1 and 2. The elastic strain to failure and plastic deformation resistance of the group 2 were determined to be 0.035 and 5∗10-3, respectively, which were significantly higher than those of group 1. The obtained results of water contact angle for group 1 revealed moderately hydrophilic properties of treated surfaces. The water contact angle was increased up to 80.85 ± 8.3 ° for group 2.",
keywords = "acid etching, biocompatibility, electron beam, sand blasting, titanium",
author = "I. Grubova and E. Chudinova and M. Surmeneva and R. Surmenev and A. Ivanova and Kravchuk, {K. S.} and Shugurov, {V. V.} and Teresov, {A. D.} and N. Koval and O. Prymak and M. Epple",
year = "2017",
month = "3",
day = "21",
doi = "10.1109/IFOST.2016.7884191",
language = "English",
pages = "69--72",
booktitle = "Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
address = "United States",

}

TY - GEN

T1 - Comparative evaluation of the sand blasting, acid etching and electron beam surface treatments of titanium for medical application

AU - Grubova, I.

AU - Chudinova, E.

AU - Surmeneva, M.

AU - Surmenev, R.

AU - Ivanova, A.

AU - Kravchuk, K. S.

AU - Shugurov, V. V.

AU - Teresov, A. D.

AU - Koval, N.

AU - Prymak, O.

AU - Epple, M.

PY - 2017/3/21

Y1 - 2017/3/21

N2 - Modification of the surface topography and chemistry are commonly used to achieve the desired biological response to the implants. The influence of the different treatment methods on the physicochemical and mechanical properties of titanium is reported. All samples were divided into 2 groups. First group was sandblasted with 250-320 μm Al2O3 at two pressures 0.45 MPa and 0.61 MPa followed by the chemical etching in a fluorine-containing solution. The second group was acid-etched in the same solution followed by electron beam modification with the energy density 8 J/cm2. The samples were investigated by SEM, EDX, XRD, nanoindentation and sessile drop method. The studies revealed that all groups have nano/micro-patterned surfaces. The EDX analysis detected only titanium in all groups. The XRD results revealed the presence of diffraction peaks corresponding to titanium. The nanoindentation studies revealed significant differences in the mechanical properties between group 1 and 2. The elastic strain to failure and plastic deformation resistance of the group 2 were determined to be 0.035 and 5∗10-3, respectively, which were significantly higher than those of group 1. The obtained results of water contact angle for group 1 revealed moderately hydrophilic properties of treated surfaces. The water contact angle was increased up to 80.85 ± 8.3 ° for group 2.

AB - Modification of the surface topography and chemistry are commonly used to achieve the desired biological response to the implants. The influence of the different treatment methods on the physicochemical and mechanical properties of titanium is reported. All samples were divided into 2 groups. First group was sandblasted with 250-320 μm Al2O3 at two pressures 0.45 MPa and 0.61 MPa followed by the chemical etching in a fluorine-containing solution. The second group was acid-etched in the same solution followed by electron beam modification with the energy density 8 J/cm2. The samples were investigated by SEM, EDX, XRD, nanoindentation and sessile drop method. The studies revealed that all groups have nano/micro-patterned surfaces. The EDX analysis detected only titanium in all groups. The XRD results revealed the presence of diffraction peaks corresponding to titanium. The nanoindentation studies revealed significant differences in the mechanical properties between group 1 and 2. The elastic strain to failure and plastic deformation resistance of the group 2 were determined to be 0.035 and 5∗10-3, respectively, which were significantly higher than those of group 1. The obtained results of water contact angle for group 1 revealed moderately hydrophilic properties of treated surfaces. The water contact angle was increased up to 80.85 ± 8.3 ° for group 2.

KW - acid etching

KW - biocompatibility

KW - electron beam

KW - sand blasting

KW - titanium

UR - http://www.scopus.com/inward/record.url?scp=85017313015&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85017313015&partnerID=8YFLogxK

U2 - 10.1109/IFOST.2016.7884191

DO - 10.1109/IFOST.2016.7884191

M3 - Conference contribution

SP - 69

EP - 72

BT - Proceedings - 2016 11th International Forum on Strategic Technology, IFOST 2016

PB - Institute of Electrical and Electronics Engineers Inc.

ER -