Coagulation and splitting of droplets of coal-water slurry containing petrochemicals and their effect on ignition characteristics

Research output: Contribution to journalArticle

3 Citations (Scopus)

Abstract

The coal-water slurries based on different types of coals and waste petrochemicals or other combustible liquids (CWSP) are very attractive for creation of cheap energetic fuel (for replacement of the coal and gas). Together with evident economic effect, the CWSP is perspective from ecological point of view. It contains a lot of water and therefore the air pollution by nitrogen and sulphur oxides is low. However, the energetic parameters of combustion of such slurry are enough far from excellence. Numerous publications were done during last years about development of new CWSP compositions as well as about improvements of its ignition and combustion techniques. The actual task is stable ignition of the slurry composition at low (critical) temperatures. In this work, we have investigated for a first time the influence of coagulation and splitting of fuel droplets onto the integral parameters of the ignition (using high-speed video-recording technique). These results clearly show the differences of ignition processes of single CWPS droplets and the aerosol flow ignition in combustion chamber. Our experiments gave the understanding of scales of co-influence of fuel droplets onto the ignition parameters. We have used the fuel compositions based on milled (particle size ∼100 μm) lignite and bituminous coal, coal-processing wastes, waste industrial oils and mazut. The investigations were done for two-body system where droplet sizes were the same (0.5–1.5 mm) at every experiment. The temperature in the combustion chamber was in range from 600 K to 1200 K. Some sequences of coagulation/splitting were observed: coagulation/splitting inside the combustion chamber; droplet coagulation before injection into the combustion volume. The influence of these processes on the ignition delay time and critical ignition temperature was defined. It was shown that splitting of the CWSP droplets leads to essential (for some times) decrease of the heating stage duration and faster ignition. Otherwise, the coagulation leads to deceleration of fuel heating and therefore to deceleration of gas-phase and heterogeneous ignition. It was shown for a first time that ignition delay time of coagulating droplets can be determined as average value between ignition delays of separate initial droplet and the droplet with the twice bigger volume. The critical ignition temperatures of separate fuel droplets are in range between temperature conditions of the splitting and coagulation. The ignition delay times of fuel fragments which appear after splitting are much lower than for initial droplets. At low temperature ignition the conditions of droplets coagulation and splitting are very important because the ignition delays durations can differ for some times. The influence of the coagulation and splitting effects becomes vanishingly small at oxidant flow temperature more than 1000 K. The obtained in this paper results should be accounted for combustion chambers working in low-temperature regime of the CWSP combustion that looks attractive from ecological, technical, economical and fire-safe points of view.

Original languageEnglish
Pages (from-to)266-277
Number of pages12
JournalApplied Thermal Engineering
Volume116
DOIs
Publication statusPublished - 1 Apr 2017

Fingerprint

Coagulation
Petrochemicals
Ignition
Coal
Water
Combustion chambers
Time delay
Temperature
Deceleration
Chemical analysis
Heating
Economic and social effects
Video recording
Bituminous coal
Industrial wastes
Slurries
Lignite
Air pollution
Gases
Oxidants

Keywords

  • Coagulation
  • Coal-water slurry containing petrochemicals
  • Droplets
  • Ignition
  • Ignition delay times
  • Splitting

ASJC Scopus subject areas

  • Energy Engineering and Power Technology
  • Industrial and Manufacturing Engineering

Cite this

@article{1734a51670c6425c9a5fde8272a2f184,
title = "Coagulation and splitting of droplets of coal-water slurry containing petrochemicals and their effect on ignition characteristics",
abstract = "The coal-water slurries based on different types of coals and waste petrochemicals or other combustible liquids (CWSP) are very attractive for creation of cheap energetic fuel (for replacement of the coal and gas). Together with evident economic effect, the CWSP is perspective from ecological point of view. It contains a lot of water and therefore the air pollution by nitrogen and sulphur oxides is low. However, the energetic parameters of combustion of such slurry are enough far from excellence. Numerous publications were done during last years about development of new CWSP compositions as well as about improvements of its ignition and combustion techniques. The actual task is stable ignition of the slurry composition at low (critical) temperatures. In this work, we have investigated for a first time the influence of coagulation and splitting of fuel droplets onto the integral parameters of the ignition (using high-speed video-recording technique). These results clearly show the differences of ignition processes of single CWPS droplets and the aerosol flow ignition in combustion chamber. Our experiments gave the understanding of scales of co-influence of fuel droplets onto the ignition parameters. We have used the fuel compositions based on milled (particle size ∼100 μm) lignite and bituminous coal, coal-processing wastes, waste industrial oils and mazut. The investigations were done for two-body system where droplet sizes were the same (0.5–1.5 mm) at every experiment. The temperature in the combustion chamber was in range from 600 K to 1200 K. Some sequences of coagulation/splitting were observed: coagulation/splitting inside the combustion chamber; droplet coagulation before injection into the combustion volume. The influence of these processes on the ignition delay time and critical ignition temperature was defined. It was shown that splitting of the CWSP droplets leads to essential (for some times) decrease of the heating stage duration and faster ignition. Otherwise, the coagulation leads to deceleration of fuel heating and therefore to deceleration of gas-phase and heterogeneous ignition. It was shown for a first time that ignition delay time of coagulating droplets can be determined as average value between ignition delays of separate initial droplet and the droplet with the twice bigger volume. The critical ignition temperatures of separate fuel droplets are in range between temperature conditions of the splitting and coagulation. The ignition delay times of fuel fragments which appear after splitting are much lower than for initial droplets. At low temperature ignition the conditions of droplets coagulation and splitting are very important because the ignition delays durations can differ for some times. The influence of the coagulation and splitting effects becomes vanishingly small at oxidant flow temperature more than 1000 K. The obtained in this paper results should be accounted for combustion chambers working in low-temperature regime of the CWSP combustion that looks attractive from ecological, technical, economical and fire-safe points of view.",
keywords = "Coagulation, Coal-water slurry containing petrochemicals, Droplets, Ignition, Ignition delay times, Splitting",
author = "Kuznetsov, {Geniy V.} and Strizhak, {Pavel A.}",
year = "2017",
month = "4",
day = "1",
doi = "10.1016/j.applthermaleng.2017.01.094",
language = "English",
volume = "116",
pages = "266--277",
journal = "Applied Thermal Engineering",
issn = "1359-4311",
publisher = "Elsevier Limited",

}

TY - JOUR

T1 - Coagulation and splitting of droplets of coal-water slurry containing petrochemicals and their effect on ignition characteristics

AU - Kuznetsov, Geniy V.

AU - Strizhak, Pavel A.

PY - 2017/4/1

Y1 - 2017/4/1

N2 - The coal-water slurries based on different types of coals and waste petrochemicals or other combustible liquids (CWSP) are very attractive for creation of cheap energetic fuel (for replacement of the coal and gas). Together with evident economic effect, the CWSP is perspective from ecological point of view. It contains a lot of water and therefore the air pollution by nitrogen and sulphur oxides is low. However, the energetic parameters of combustion of such slurry are enough far from excellence. Numerous publications were done during last years about development of new CWSP compositions as well as about improvements of its ignition and combustion techniques. The actual task is stable ignition of the slurry composition at low (critical) temperatures. In this work, we have investigated for a first time the influence of coagulation and splitting of fuel droplets onto the integral parameters of the ignition (using high-speed video-recording technique). These results clearly show the differences of ignition processes of single CWPS droplets and the aerosol flow ignition in combustion chamber. Our experiments gave the understanding of scales of co-influence of fuel droplets onto the ignition parameters. We have used the fuel compositions based on milled (particle size ∼100 μm) lignite and bituminous coal, coal-processing wastes, waste industrial oils and mazut. The investigations were done for two-body system where droplet sizes were the same (0.5–1.5 mm) at every experiment. The temperature in the combustion chamber was in range from 600 K to 1200 K. Some sequences of coagulation/splitting were observed: coagulation/splitting inside the combustion chamber; droplet coagulation before injection into the combustion volume. The influence of these processes on the ignition delay time and critical ignition temperature was defined. It was shown that splitting of the CWSP droplets leads to essential (for some times) decrease of the heating stage duration and faster ignition. Otherwise, the coagulation leads to deceleration of fuel heating and therefore to deceleration of gas-phase and heterogeneous ignition. It was shown for a first time that ignition delay time of coagulating droplets can be determined as average value between ignition delays of separate initial droplet and the droplet with the twice bigger volume. The critical ignition temperatures of separate fuel droplets are in range between temperature conditions of the splitting and coagulation. The ignition delay times of fuel fragments which appear after splitting are much lower than for initial droplets. At low temperature ignition the conditions of droplets coagulation and splitting are very important because the ignition delays durations can differ for some times. The influence of the coagulation and splitting effects becomes vanishingly small at oxidant flow temperature more than 1000 K. The obtained in this paper results should be accounted for combustion chambers working in low-temperature regime of the CWSP combustion that looks attractive from ecological, technical, economical and fire-safe points of view.

AB - The coal-water slurries based on different types of coals and waste petrochemicals or other combustible liquids (CWSP) are very attractive for creation of cheap energetic fuel (for replacement of the coal and gas). Together with evident economic effect, the CWSP is perspective from ecological point of view. It contains a lot of water and therefore the air pollution by nitrogen and sulphur oxides is low. However, the energetic parameters of combustion of such slurry are enough far from excellence. Numerous publications were done during last years about development of new CWSP compositions as well as about improvements of its ignition and combustion techniques. The actual task is stable ignition of the slurry composition at low (critical) temperatures. In this work, we have investigated for a first time the influence of coagulation and splitting of fuel droplets onto the integral parameters of the ignition (using high-speed video-recording technique). These results clearly show the differences of ignition processes of single CWPS droplets and the aerosol flow ignition in combustion chamber. Our experiments gave the understanding of scales of co-influence of fuel droplets onto the ignition parameters. We have used the fuel compositions based on milled (particle size ∼100 μm) lignite and bituminous coal, coal-processing wastes, waste industrial oils and mazut. The investigations were done for two-body system where droplet sizes were the same (0.5–1.5 mm) at every experiment. The temperature in the combustion chamber was in range from 600 K to 1200 K. Some sequences of coagulation/splitting were observed: coagulation/splitting inside the combustion chamber; droplet coagulation before injection into the combustion volume. The influence of these processes on the ignition delay time and critical ignition temperature was defined. It was shown that splitting of the CWSP droplets leads to essential (for some times) decrease of the heating stage duration and faster ignition. Otherwise, the coagulation leads to deceleration of fuel heating and therefore to deceleration of gas-phase and heterogeneous ignition. It was shown for a first time that ignition delay time of coagulating droplets can be determined as average value between ignition delays of separate initial droplet and the droplet with the twice bigger volume. The critical ignition temperatures of separate fuel droplets are in range between temperature conditions of the splitting and coagulation. The ignition delay times of fuel fragments which appear after splitting are much lower than for initial droplets. At low temperature ignition the conditions of droplets coagulation and splitting are very important because the ignition delays durations can differ for some times. The influence of the coagulation and splitting effects becomes vanishingly small at oxidant flow temperature more than 1000 K. The obtained in this paper results should be accounted for combustion chambers working in low-temperature regime of the CWSP combustion that looks attractive from ecological, technical, economical and fire-safe points of view.

KW - Coagulation

KW - Coal-water slurry containing petrochemicals

KW - Droplets

KW - Ignition

KW - Ignition delay times

KW - Splitting

UR - http://www.scopus.com/inward/record.url?scp=85012289404&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85012289404&partnerID=8YFLogxK

U2 - 10.1016/j.applthermaleng.2017.01.094

DO - 10.1016/j.applthermaleng.2017.01.094

M3 - Article

VL - 116

SP - 266

EP - 277

JO - Applied Thermal Engineering

JF - Applied Thermal Engineering

SN - 1359-4311

ER -