If you made any changes in Pure these will be visible here soon.

Research Output

Filter
Conference contribution

The influence of classical and modern manufacturing technologies on the properties of metal dental bridges

Cotruţ, C. M., Ciucǎ, S., Miculescu, F., Antoniac, I., Târcolea, M. & Vrânceanu, D. M., 1 Jan 2014, BiomMedD V. p. 163-168 6 p. (Key Engineering Materials; vol. 583).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

2 Citations (Scopus)

Stainless steel brackets: In vitro corrosion behaviour and mechanical debonding test

Cotruţ, C. M., Târcolea, M., Vrânceanu, M. D., Gherghilescu, A. I., Ghiban, N., Baciu, F. & Ionescu, I. C., 1 Jan 2014, Advanced Materials and Structures V. Trans Tech Publications Ltd, p. 187-193 7 p. (Solid State Phenomena; vol. 216).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Optimisation of magnets positions on the knee joint using comsol multiphysics

Laptoiu, D. C., Antoniac, I. & Cotrut, C., 1 Jan 2011, Annals of DAAAM for 2011 and Proceedings of the 22nd International DAAAM Symposium "Intelligent Manufacturing and Automation: Power of Knowledge and Creativity". Danube Adria Association for Automation and Manufacturing, DAAAM, p. 935-936 2 p. (Annals of DAAAM and Proceedings of the International DAAAM Symposium).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Investigation of the hard films deposited by PVD-magnetron sputtering on the cutting tools

Vlasceanu, D., Cotrut, C., Tarcolea, M., Baciu, F. & Nicodim, M., 1 Jan 2008, Annals of DAAAM for 2008 and Proceedings of the 19th International DAAAM Symposium "Intelligent Manufacturing and Automation: Focus on Next Generation of Intelligent Systems and Solutions". Danube Adria Association for Automation and Manufacturing, DAAAM, p. 1487-1488 2 p. (Annals of DAAAM and Proceedings of the International DAAAM Symposium).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Effect of calcium content on the microstructure and degradation of Mg-Ca binary alloys potentially used as orthopedic biomaterials

Blajan, A. I., Miculescu, F., Ciuca, I., Cotrut, C., Semenescu, A. & Antoniac, I., 1 Jan 2014, BiomMedD 2014. Iulian, A., Marian, M., Cosmin, S. & Madalina, A. (eds.). Trans Tech Publications Ltd, p. 104-108 5 p. (Key Engineering Materials; vol. 638).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

2 Citations (Scopus)

Corrosion behavior of TiSiN coatings deposited on Ni-Cr alloy in artificial saliva with and without fluoride

Dinu, M., Braic, M., Tarcolea, M., Vladescu, A., Antoniac, I. & Cotrut, C. M., 1 Jan 2014, BiomMedD 2014. Iulian, A., Marian, M., Cosmin, S. & Madalina, A. (eds.). Trans Tech Publications Ltd, p. 47-53 7 p. (Key Engineering Materials; vol. 638).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Corrosion behavior of Ti and Ti based alloys used as implants-supported mandibular overdentures

Meghea, D., Miculescu, M., Cotruţ, C. M., Bane, M., Gherghilescu, A. & Vrânceanu, D. M., 1 Jan 2014, BiomMedD 2014. Iulian, A., Marian, M., Cosmin, S. & Madalina, A. (eds.). Trans Tech Publications Ltd, p. 31-37 7 p. (Key Engineering Materials; vol. 638).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)